Top 9 Pixhawk Power Module – Hobby Remote & App Controlled Vehicle Parts

As an Amazon Associate I earn from qualifying purchases.

1. elechawk

#ad

Pixhawk Power Module 5.3V BEC XT60 Connectors for APM2.8 2.6 Quadcopter

#ad
elechawk #ad - 6-pin 1. 25 connector suitable for Pixhawk/APM. There is a 220uf electrolytic capacitor in the Power Module can effectively prevent destroyed by a high voltage pulse. Used up to 28v 6s lipo and at a maximum of 90A. Maximum bec output continuous current: 2. 25a. The power module is ready to use with XT60 connectors pre-fitted, and shrink wrapped for protection. The outputs voltage of bec is about 5. 3v.
Brandelechawk #ad
Manufacturerelechawk #ad
Part Number3867

2. Hobbypower

#ad

Hobbypower Power Module V1.0 for Pixhawk Apm2.5 Apm2.6 Ardupilot Mega Flight Controller

#ad
Hobbypower #ad - Newest version, have soldered already, ready to work! Top quality and 100% brand new. Voltage and current measurement configured for 5V ADC. Input voltage: 6~28V support 30V. Max current sensing: 90A.
BrandHobbypower #ad
ManufacturerHobbypower #ad
Weight0.02 Pounds
Part Number4977
Model4977

3. powerday

#ad

Powerday APM Power Module V1.0 XT60 Female Male Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller

#ad
powerday #ad - Voltage and current measurement configured for 5V ADC. Use your aircraft's own ESC/BEC for that. It is not designed to power servos. Max input voltage: 30V, Max current sensing: 90A. 6-pos df13 cable plugs directly to APM 2. 5's 'pm' connector. Note: the power module is only designed to power apm, a rc receiver and APM accessories GPS, 3DR radio. Switching regulator outputs 5. 3v and 3A max.
Brandpowerday #ad
ManufacturerRcmodel #ad
Height0.5 Inches
Length7 Inches
Weight0.04 Pounds
Width1.2 Inches
Part Number49122-1
Model49122

4. HobbySoar

#ad

HobbySoar Power Module Output BEC 3A with XT60 Plug for APM2.5 APM2.6 APM2.8 APM Pixhawk Flight Controller

#ad
HobbySoar #ad - It is not designed to power servos. Note: the power module is only designed to flight controller, 3dr radio. The power module comes completely assembled with XT60 connectors, and wrapped in shrink tubing for protection.

Pls do not use this to power the servo. Otherwise, rc receiver and APM accessories GPS, it will seriously affect the reliability of the flight control equipment. If the kit is equipped with a servo, due to the large current of servo system, please use the BEC to power the servo system. The apm power module is a simple way of providing your APM FC with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pin cable. For sale is power module which is compatible with APM2. 5/2. 6, pixhawk flight controller, have soldered already, ready to work!. Input voltage: 6~28v, max current sensing: 90A.
BrandHobbySoar #ad
ManufacturerShareGoo #ad
Weight0.04 Pounds
Part Number43234-2762

5. Hobbypower

#ad

Hobbypower Power Module V1.0 with XT60 Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller

#ad
Hobbypower #ad - The power module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection. Used to detect the battery voltage and the battery current, calculate the remaining battery power, flight control board receives two signals, estimate the remaining flight time.

The on-board switching regulator outputs 5. 3v and a maximum of 2. 25a from up to a 4S LiPo battery. The apm power module is a simple way of providing your apm fc with clean power from a lipo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable.

Another signal cable connectors are used in Japan original fittings, so APM flight control board and reliable connection between the power supply module. In addition the module also comes with bec function, non-domestic joint, you can output 5. 3 dc, 3a maximum continuous current for the flight control board to provide a stable power supply.
BrandHobbypower #ad
ManufacturerHobbypower #ad
Part NumberPower Module

6. Mauch Electronics

#ad

4-14 Cell Battery, 200 Amps, Mauch Electronics Pixhawk 2.1 Power Module Upgrade

#ad
Mauch Electronics #ad - Includes factory tested calibration values for easy, accurate information. Rated for up to 14S voltage and 200A current. Drop-in upgrade for your Pixhawk/Pixhawk 2. 1 power module. See our amazon storefront for other voltage/current combinations. Genuine mauch components from authorized US reseller.
BrandMauch Electronics #ad
ManufacturerMauch Electronics #ad
Part NumberPL 4-14S / 3A Combo - 200A

7. elechawk

#ad

Pixhawk4 Power Module with 5.3V BEC XT60 for PXFmini CUAV v5 Mini Pix Pixracer Quadcopter GH Connector

#ad
elechawk #ad - Gh1. 25 connector suitable for pixhawk4, Mini Pix, CUAV v5, PXFmini, Pixracer. Maximum bec output continuous current: 2. 25a. The outputs voltage of bec is about 5. 3v. Used up to 28v 6s lipo and at a maximum of 90A. There is a 220uf electrolytic capacitor in the Power Module can effectively prevent destroyed by a high voltage pulse.
Brandelechawk #ad
Manufacturerelechawk #ad
Weight0.06 Pounds
Part Number7885

8. Yoton

#ad

Color: XT60 Connector, Accessories APM 2.5 2.6 2.8 Pixhawk Power Module 30V 90A with 5.3V DC BEC Available with T or XT60 for RC Helicopter Part

#ad
Yoton #ad - Upgrade parts/accessories: Adapter. Color: xt60 Connector. Material: Composite Material. Use: vehicles & Remote Control Toys. Size: /.
BrandYoton #ad
ManufacturerYoton #ad
Part NumberYTN-B60C3B33A0B45A837DD6AEF323084E1A

9. Yoton

#ad

Yoton Accessories APM 2.5 2.6 2.8 Pixhawk Power Module 30V 90A with 5.3V DC BEC Available with XT60 for RC Helicopter Part

#ad
Yoton #ad - Four-wheel drive attributes: Assemblage. For vehicle type: Helicopters. Use: vehicles & Remote Control Toys. Tool supplies: Assembly Category. Model number: XT60 .
BrandYoton #ad
ManufacturerYoton #ad
Part NumberYTN-71B775A3C0AE4A6DECDAE3D7720391A1